.product_section .product_form, .product_gallery { opacity: 1; } .multi_select, form .select { display: block !important; } .image-element__wrap { display: none; }

How to Fix the Speaker Wire Connector and Make it Good Again

November 20, 2021 1 min read

Speaker wire can operate poorly for a variety of reasons ranging from degradation of the wire casing along the length of the wire, which can cause wire wear and fraying, to fraying at the end of the wire which causes a poor connection, leading to bad sound. With a little skill with a soldering iron, you can usewire solder to repair a frayed wire or bad connection, and electrical tape to re-cover an exposed wire.

Is your speaker no longer providing you with the best sound quality? Your speaker connection might not be as efficient as it once was. You can repair the speaker wire connector and make it perfect again.

But how? This article presents the complete procedure of repairing the speaker wire connector.

PROCESS OF REPAIRING SPEAKER WIRE CONNECTOR:

Below is the complete process of repairing speaker wire connectors:

Strip the wire insulation about ½ an inch from each side.
Twist the two bare wires that you have to connect.
Apply soldering material on the bare wire and heat it using the solder stick.
Put insulation tape on the newly formed connection to insulate it.
Your connection is ready.

WHY DO YOU USE SOLDERING AS A CONNECTION?

Soldering is the best form of creating a speaker connection. Besides, you don’t need any connectors to form the connection. Thus, making it an easier way to repair the speaker wire connector.

Catalog

View All

SOLDERSTICK WATERPROOF SOLDER WIRE CONNECTOR KIT
$24.99

Secured and Waterproof Wiring Connections in Literally Seconds! SolderStick eliminates the hassle and allows you to focus on rewiring done the right way.

View
300pcs SolderStick Ring/Eyelets Connector Set
$59.95

Thick copper barrel ensures strong secure crimping every time, providing minimal voltage drop, high current flow, and less heat. These will prevent short circuits and problematic wiring that inferior connectors are known for. Insulation tubing has unique dual-walled design. High quality 3:1 shrinkage tubing has a heat-activated sealant lining to provide a 360-degree secure seal. It's flame-retardant, waterproof, and can be used underground Package includes: Total 300 PCS Heat Shrink Ring Connectors. Wire range: 22-18 ( red ) / 16-14 ( blue ) / 12-10 ( yellow ) A.W.G. Copper barrel is an excellent conductor of electricity, corrosion resistant and has a very high melting point. These salient features will generate minimal heat while maintaining a high current flow with minimal voltage drop. COMPLIANT WITH ALL ELECTRICAL STANDARDS – SolderStick heat shrink connectors are compliant with ROHS, ISO 9001:2008, SGS and CE standards. Total: 300pcs100pcs Red(M5#10: 25pcs, M6 1/4”: 25pcs, M8 5/16”: 25pcs, M10 3/8”: 25pcs)100pcs Blue((M5#10: 25pcs M6 1/4”: 25pcs, M8 5/16”: 25pcs,M10 3/8”: 25pcs)100pcs Yellow ((M5#10: 25pcs, M6 1/4”: 25pcs, M8 5/16”: 25pcs, M10 3/8”: 25pcs) Specifications 100 RedWire range: 0.5~1.5mm², A.W.G.:22~18, Maximum current = 19A100 BlueWire range: 1.5~2.5mm², A.W.G.:16~14, Maximum current = 27A100 YellowWire range: 4~6mm², A.W.G.:12~10, Maximum current = 48A

View
400pcs Spade Connectors Kit
$49.99

Thick brass in the wire connectors ensures strong secure crimping every time, providing small voltage drop, high current flow, and less heat. These will prevent short circuits and problematic wiring that inferior knockoff connectors are known for. How To Use

View
T-Tap Wire Connectors
$29.99

Tap into any wire with ease using our T-Type Quickconnection terminals! T-Tap Connectors are used to tap into an existing wire. Closing the quick slide connector makes a connection to the wire that can be accessed using a push-on terminal. T-Tap Wire Terminals allow you to tap an existing wire with another wire with ONE crimp and no additional connections. No wire stripping is necessary. Simply clip part over the primary wire and close with a pair of pliers No special tools are required Taps are insulated, color coded by wire size All taps meet or exceed UL and SA standards HOW TO USE: Simply insert both wires into the splice, squeeze down on the metal insert with pliers, and close the cap. SPECIFICATIONS: Quantity: 120 PCS Material: Nylon, Copper, Tin Maximum Operating Temperature: 221 °F Maximum Recommended Voltage Rating: 600 V Box Size: 20cm x 15cm x 5cm Package Weight: 0.35 kg PACKAGE INCLUDES: 20 x Red Connectors 20 x Blue Connectors 20 x Yellow Connectors 20 x Red T-Tap Wire Terminals 20 x Blue T-Tap Wire Terminals 20 x Yellow T-Tap Wire Terminals

View
164pcs Color-Coded Heat Shrink Tubing
$24.99

✔️ EASY AND FAST PROCESS All-in-one step solder and seal process. Shrink quickly, durable and evenly with our 2:1 shrink ratio polyolefin tubing to create a tight bond with connecting wires. ✔️ STAY ORGANIZED Our connectors come within a storage box, easy to store and carry. You can throw the heat shrink tubing kit in your toolbox and not have to worry about size getting mixed together. ✔️ ENVIRONMENTAL FRIENDLY AND SAFE Made of polyolefin, soft and flexible, acid and alkali resistance, anti-aging. This ensures that wires are tightly connected and prevents wires slipping out of the terminal. ✔️ WIDE APPLICATIONS Provide a barrier between cables and corrosive chemicals, insulate cables and wires against extreme heat in aircraft, boats, and military-grade vehicles. Suitable for electrical insulation, strain relief, cable bonding, color-coding, and identification. Specification： 60pcs 1.0 x 40mm Heat Shrink Tubing Set 30pcs 2.0 x 40mm Heat Shrink Tubing Set 20pcs 3.0 x 40mm Heat Shrink Tubing Set 16pcs 4.0 x 40mm Heat Shrink Tubing Set 12pcs 6.0 x 40mm Heat Shrink Tubing Set 10pcs 8.0 x 80mm Heat Shrink Tubing Set 8pcs 10.0 x 80mm Heat Shrink Tubing Set 8pcs 14.0 x 80mm Heat Shrink Tubing Set

View